Hw-module Slot
Hw-module subslot card slot/subslot number shutdown unpowered. Example: Device(config)# hw-module subslot 1/0 shutdown unpowered: Powers down the specified module by placing it in low power mode. Example: Device(config)# end: Exits the global configuration mode. No Hw Module Slot 1 Oversubscription on your country, as many bonuses are only valid to players from certain countries. However, other ranging factors, such as the bonus value No Hw Module Slot 1 Oversubscription and the casino's rating, have been added into the mix as well. Hw-module module. The CLI will only give you the further option of 'shutdown' if the service module supports it eg. An FWSM does support shutdown so you would get the option in the above command. A CSM does not support shutdown so you would only get the option to reload.
My wonderful Kiwi Cattools is doing configuration backup of devices every 15 minutes. Two times till now it happened to me that different ASA SSM modules are stopping to respond on ssh configuration requests.After getting the status of the module; the status show up as: Unresponsive
fw-01# show module 1 details
Getting details from the Service Module, please wait...
Unable to read details from slot 1
ASA 5500 Series Security Services Module-20
Model: ASA-SSM-20
Hardware version: 1.0
Serial Number: JAF1535CKBP
Firmware version: 1.0(11)5
Software version: 7.1(6)E4
MAC Address Range: 44d3.ca8e.06f8 to 44d3.ca8e.06f8
App. name: IPS
App. Status: Not Applicable
App. Status Desc: Not Applicable
App. version: 7.1(6)E4
Data plane Status: Not Applicable
Status: Unresponsive
Only way to do it is to reset the module using command:hw-module module 1 shutdown
Shutdown module in slot 1? [confirm]
Shutdown issued for module in slot 1
fw-01# show module 1 details
Getting details from the Service Module, please wait...
Unable to read details from slot 1
ASA 5500 Series Security Services Module-20
Model: ASA-SSM-20
Hardware version: 1.0
Serial Number: JAF1535CKBP
Firmware version: 1.0(11)5
Software version: 7.1(6)E4
MAC Address Range: 44d3.ca8e.06f8 to 44d3.ca8e.06f8
App. name: IPS
App. Status: Not Applicable
App. Status Desc: Not Applicable
App. version: 7.1(6)E4
Data plane Status: Not Applicable
Status: Down
fw-01# hw-module module 1 reset
The module in slot 1 should be shut down before
resetting it or loss of configuration may occur.
Reset module in slot 1? [confirm]
Reset issued for module in slot 1
Now you need to wait for a while (about2 minutes during Initialization state):
fw-01# show module 1 details
Getting details from the Service Module, please wait...
Unable to read details from slot 1
ASA 5500 Series Security Services Module-20
Model: ASA-SSM-20
Hardware version: 1.0
Serial Number: JAF1535CKBP
Firmware version: 1.0(11)5
Software version: 7.1(6)E4
MAC Address Range: 44d3.ca8e.06f8 to 44d3.ca8e.06f8
App. name: IPS
App. Status: Not Applicable
App. Status Desc: Not Applicable
App. version: 7.1(6)E4
Data plane Status: Not Applicable
Status: Init
After about 2 minutes you will get correct status output for SSM module:
fw-01# show module 1 details
Getting details from the Service Module, please wait...
ASA 5500 Series Security Services Module-20
Model: ASA-SSM-20
Hardware version: 1.0
Serial Number: JAF1535CKBP
Firmware version: 1.0(11)5
Software version: 7.1(6)E4
MAC Address Range: 44d3.ca8e.06f8 to 44d3.ca8e.06f8
App. name: IPS
App. Status: Up
App. Status Desc: Normal Operation
App. version: 7.1(6)E4
Data plane Status: Up
Status: Up
Mgmt IP addr: 10.10.212.21
Mgmt Network mask: 255.255.255.0
Mgmt Gateway: 10.10.212.1
Mgmt Access List: 10.20.150.0/23
Mgmt Access List: 10.30.150.0/23
Mgmt web ports: 443
Mgmt TLS enabled: true
Useful links:
1. Configuring the ASA 5500 AIP SSM2. Configuring the ASA 5500 AIP SSM - PDF
Can anyone comment on RSP redundancy with SSO mode?
I have a test 7507 with rsp-k4pv-mz.120-32.S8.bin on both RSP2s. I've done
this:
service single-slot-reload-enable
redundancy
no keepalive-enable
mode sso
And it doesn't seem to ever sync the slave
ranttest#show red
Redundant System Information :
------------------------------
Available system uptime = 14 minutes, 49 seconds
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = hsa
Maintenance Mode = Disabled
Communications = Down Reason: Simplex mode
Current Processor Information :
-------------------------------
Active Location = slot 2
Current Software state = ACTIVE
Uptime in current state = 13 minutes, 24 seconds
Image Version = Cisco Internetwork Operating System
Software
IOS (tm) RSP Software (RSP-K4PV-M), Version 12.0(32)S8, RELEASE SOFTWARE
Hw-module Beacon Slot
(fc1)Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Mon 20-Aug-07 16:34 by leccese
BOOT =
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Peer (slot: 3) information is not available because it is in 'DISABLED'
state
ranttest#redundancy force-switchover
Cannot perform switchover until the standby is fully initialized.
The box is up, its got two OSPF adjacencies, maybe a hundred routes - its
not doing anything fancy, so I'm kind of stuck here. The production target
is 7507s /w RSP4s, the same OSPF, and about 180k routes via BGP. Any idea
Hw-module Slot 1 Oversubscription
what might be wrong here?
_______________________________________________
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/